The Atwood Air Command Rooftop RV Air Conditioner w/ Heat Pump # AT15033-22 comes with everything you'll need to install it on your 2009 Holiday Rambler Endeavor that has the roof duct system already present. view full answer...
We have the Replacement RV Toilet Floor Flange # T05-0784 which has a 4 inch diameter hole and .541 inches of usable female threads. But if you need something 4 inches long where the threads are we do not have anything. view full answer...
Yes, since your 2019 Holiday Rambler Vacationer 35P is built on the Ford F-53 chassis and it has a GVWR of 24,000 pounds the Roadmaster Reflex Steering Stabilizer # RM-RBK25-RSSA you referenced is the correct kit and it will work perfectly. This will do a great job of keeping the RV in line during travel by mounting between the steering mechanism and chassis and constantly working to maintain its position.
All the custom mounting brackets are included. I have attached a short video demonstration... view full answer...
We have the exact steering stabilizer you need for your 2019 Holiday Rambler Admiral 29M built on a Ford F-53 chassis, which is the following part:
- Roadmaster Exact Center Steering Stabilizer # RM33RR
This will do a really nice job of centering your rig, allowing for much better handling of your motorhome. view full answer...
Since the landing gear feet of your 2019 Holiday Rambler Navigator 37R are 10 inches and round the correct set of SnapPads would be the part # SP64FR74 that you referenced. view full answer...
Yes. According to my research, the FWD models of the 2019 Ford Edge SEL should be towed using a dolly; I would recommend checking your vehicle's owner's manual to confirm this information. The Demco Kar Kaddy SS Tow Dolly # DM9713045 is the perfect solution to accomplish this as long as the distance between the outside tire treads on your vehicle is less than 76".
On top of the hydraulic disc brakes that make this tow dolly a great choice, the EZ latch surge coupler eliminates the need... view full answer...
We do have replacement lift motors available for a Fan-Tastic vent, but 2000 TS is not actually a model number. To find out which lift motor you need there should be a number 7 or 17 on the actual motor, which is the RPMs of that motor.
If the motor has a 7 on it the correct replacement is Replacement Lift Motor for Fan-Tastic Vent B Series Roof Vents and we no longer have it available, if it has 17 on it then the correct part is # FVK6010-81 (White) or # FVK6010-80 (Off-White). view full answer...
When installing a bearing like the Bearing, 42MM Nev-R-Lube 42MM x 76MM x 39MM # 31-73-3 the nut should be torqued to 145-155 ft. lbs. view full answer...
The only slide slickers we carry are the Lippert Carpet Protectors for RVs with Slide Outs # LC134993 which measure 40" long x 5" wide. This will be a standard size and should be able to fit a wide variety of slide out sizes. view full answer...
So there is a single option available for a bike rack that is approved for use on an RV (both a motorhome like yours and a trailer should you have one or go that route in the future) and has the ability to carry four 60 lb electric bikes, which is from Let's Go Aero. It is actually a 2-bike rack with an add-on, so what you will need is the following:
- Lets Go Aero V-Lectric FAT PRO Bike Rack for 2 Electric Bikes # LGA77FR
- 2-Bike Add-On for Lets Go Aero V-Lectric Electric Bike Rack... view full answer...
A brake controller is going to need to be hardwired into your 2002 Holiday Rambler Endeavor because there is no plug available. In order to do this (since I assume it already has a 6-pin wiring harness in the back) you will need to cut that and connect it to the Universal Brake Controller Wiring Kit # ETBC7 using a circuit tester such as # PTW2993 to test the functions. You will also likely need extra wire # 10-2-1 and butt connectors # DW05745-10 for this installation. I have added links... view full answer...
For starters, I have attached a photo of how the Universal-Design Rocker Switch part # PK34360 should be wired. However, I believe the issue you are having is in regards to the size of wire used. The correct size or (gauge) will vary depending on factors such as amp draw and length of wire.
The wires running from the heater to the splice can be anywhere from 16 gauge - 10 gauge depending on length. However, once the three heater wires are spliced together and traveling to the switch you... view full answer...
Good question, because the best thing you can do by far on your motorhome is to install a rear anti-sway bar because they are a vast improvement over the OEM sway bars with thicker construction for the greatest reduction in sway and improvement in overall handling. After that you can further improve the ride by adding a front anti-sway bar, but definitely start with a rear anti-sway bar. The fits for your 2017 Holiday Rambler Endeavor motorhome with V-Ride suspension are the following:
-... view full answer...
I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part # LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch with the new one that comes with the kit. view full answer...
The Atwood Air Command Rooftop RV Air Conditioner part # AT15028-22 comes with everything you will need to install on your 2007 Holiday Rambler Toy Hauler. There will not be an additional wiring or base plates needed. It comes with the wiring harness for the thermostat as well as for the unit itself. The hardware to attach the unit to your roof is also included for you as well as all the foam gaskets and vent covers etc. view full answer...
Yes, if you were looking to replace the PD9155 in your RV the part # PD9160A would fit and work well. It provides the same function of converting 120 volt power to 12 volt power up to 60 amps. view full answer...
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the #... view full answer...
You can easily replace the thermostatically controlled RV ceiling fan you have in your 1999 Holiday Rambler Endeavor 37WDS with one that does not have that feature. We have the Ventline Ventadome Trailer Roof Vent part # V2094SP-28 which fits the standard 14 inch by 14 inch rough cut RV roof opening and has a fan without a thermostat. view full answer...
Yes, the Curt Trailer Hitch Receiver part # C15810 which is a fit for your 2008 Ford F-350 will allow you to tow your 2000 Holiday Rambler Aluma Lite 30SKS without the use of a weight distribution system assuming the figures you provided on the trailer are correct. This hitch has a 20,000 lbs gross trailer weight (GTW) and 2,700 lb tongue weight (TW) rating with a 2-1/2" receiver tube opening.
According to the instructions for this hitch, the professional installation time is 30 minutes... view full answer...
Go To Results